bf30012c-2d18-4a0c-a504-e8089991e623 Modified mineral mortar, group 1 Modifizierte mineralische Mörtel, Gruppe 1 Mineralische Baustoffe Bindemittel Zement 02 Building products Masonry and related products Mineral factory-made mortar Modified mineral mortars are combinations of one or more inorganic binders, fillers, aqueous dispersions or dispersion powders, water and if necessary additives. They comply with manifold, often specific, functions in the construction, furnishing and refurbishment of buildings. The product displaying the highest environmental impacts was used as a representative product for calculating the Life Cycle Assessment results (worst-case approach). 0 2022 2027 2022-09-26 Modified mineral mortars are combinations of one or more inorganic binders, fillers, aqueous dispersions or dispersion powders, water and if necessary additives. They comply with manifold, often specific, functions in the construction, furnishing and refurbishment of buildings. According to the Model EPD system (IBU) and the guideline and the substance list (available for members of the trade associations FEICA, EFCC, IVK and DBC), the environmental impacts of the substances are condensed to a single score; the single score of a formulation is calculated based on the single score of the substances. The products are grouped according to their single score (group 1 to 3), the formulation displaying the highest environmental impacts was used as a representative product for calculating the Life Cycle Assessment results (worst-case approach). Technical data: The density of the products is between 0,80 and 1,70 g/cm³, other relevant technical data can be found in the manufacturer’s technical documentation. Construction products with Declaration of Performance in accordance with CPR and the manufacturer's technical documentation: Module 1: Modified mineral mortars as repair mortar for the protection and repair of concrete structures 1.1 Products used to restore and/or replace defective concrete The requirements on essential characteristics for all intended uses in accordance with EN 1504-3, Tables 1 and 3, must be maintained. These are: - Compressive strength (EN 12190) - Chloride ion content (EN 1015-17) - Adhesive strength by pull-off test (EN 1542) 1.2 Products to protect reinforcement The requirements on essential characteristics for all intended uses in accordance with EN 1504-7, Table 1, must be maintained. This is - Corrosion protection (EN 15183) Further essential characteristics in accordance with the manufacturer's technical documentation/declaration of performance Module 2: Adhesives based on modified mineral mortars 2.1 Products for bonding ceramic tiles as well as natural stone for internal and external installations on walls, floors and ceilings The requirements on essential characteristics according to EN 12004, Table 1, must be maintained. These are: - Tensile adhesion strength after dry storage (EN 12004-2) - Tensile adhesion strength after water immersion (EN 12004-2) - Tensile adhesion strength after heat ageing (EN 12004-2) - Tensile adhesion strength after freeze/thaw cycles (EN 12004-2) - Open time: Tensile strength (EN 12004-2) Further essential characteristics in accordance with the manufacturer's technical documentation/declaration of performance 2.2 The minimum requirement of EAD 040083-00-0404 External Thermal Insulation Composite Systems with Rendering must be maintained. The essential characteristics are to be specified in accordance with the European technical assessment (ETA, specification no.). Further essential characteristics in accordance with the manufacturer's technical documentation/declaration of performance Module 3: Modified mineral mortars as joint fillers The minimum requirements of EN 13888 must be maintained. Module 4: Modified mineral mortars as screed, floor levelling compounds, fillers, flowing screed The requirements on essential characteristics according to EN 13813 ‘Screed material and floor screeds – Screed materials – Properties and requirements’ must be maintained. For synthetic resin screeds, these are: - Bond strength (EN 13892-8) - Reaction to fire (EN 13501-1) Further essential characteristics in accordance with the manufacturer's technical documentation/declaration of performance Module 5: Modified mineral mortars as levelling compounds for walls and ceilings Module 5.1: The minimum requirements of EN 998-1 apply. These are: - Reaction to fire (EN 13501-1) - Compressive strength - Dry bulk density - Capillary water absorption - Water vapour permeability Further essential characteristics in accordance with the manufacturer's technical documentation/declaration of performance Module 5.2: The minimum requirements of EN 13279 apply. Further essential characteristics in accordance with the manufacturer's technical documentation/declaration of performance Module 6: Modified mineral mortars as grouts The requirements of DAfStb Guideline on 'Production and use of cement-bound flow concrete and grouting mortar' (VeBMR) must be maintained. The requirements according to MVV TB No. C 2.1.4.5 for "Ü-mark" must be maintained. Module 7: Modified mineral mortars for liquid applied products for waterproofing of buildings 7.1 The requirements according to EN 14891 , table 1, must be maintained. These are: - initial tensile adhesion strength EN 14891 - Tensile adhesion strength after water contact EN 14891 - Waterproofing EN 14891 - Crack bridging ability EN 14891 7.2 The minimum requirements of the 'Testing principles for granting general building authority approved test certificates for waterproofing with mineral waterproofing slurries and flexible polymer modified thick coatings' (PG MDS/FPD) must be maintained. The characteristics for the proof of usability are to be specified in accordance with the test principles for granting general building authority test certificates for waterproofing with mineral waterproofing slurries and flexible polymer thick coatings. 7.3 The minimum requirements of the 'testing principles for granting general building authority approved test certificates for waterproofing in conjunction with ceramic tiles' (PG AIV) must be considered. 7.4 The minimum requirement of EAD 030295-00-0605 must be maintained. The essential characteristics are to be specified in accordance with the European technical assessment (ETA, specification no.). Module 8: Modified mineral mortars for waterproofing floors and/or walls inside buildings The minimum requirement of EAD 030352-00-0503 must be maintained. The essential characteristics are to be specified in accordance with the European technical assessment (ETA, specification no.). Declared unit: This EPD refers to the declared unit of 1 kg of modified mineral mortar, group 1; applied into the building with a density of 800 - 1,700 kg/m³ in accordance with the IBU PCR part B for Mineral Factory-Made Mortars. The results of the Life Cycle Assessment provided in this declaration have been selected from the product with the highest environmental impact (worst-case scenario). Depending on the application, a corresponding conversion factor such as the density to convert volumetric use to mass must be taken into consideration. The Declaration type is according to EN 15804: Cradle to gate with options, modules C1–C4, and module D (A1–A3, C, D) and additional modules (A4-A5). Modifizierte mineralische Mörtel sind Kombinationen aus einem oder mehreren anorganischen Bindemitteln, Füllstoffen, wässrigen Dispersionen oder Dispersionspulvern, Wasser und ggf. Zusatzstoffen. Sie erfüllen vielfältige, oft spezifische Funktionen beim Bauen, Einrichten und Sanieren von Gebäuden. Nach dem Muster-EPD-System (IBU) und dem Leitfaden und der Stoffliste (erhältlich für Mitglieder der Fachverbände FEICA, EFCC, IVK und DBC) werden die Umweltwirkungen der Stoffe zu einer Einzelpunktzahl verdichtet; die Einzelpunktzahl einer Formulierung wird auf der Grundlage der Einzelpunktzahl der Stoffe berechnet. Die Produkte werden entsprechend ihrer Einzelpunktzahl in Gruppen eingeteilt (Gruppe 1 bis 3), wobei die Formulierung mit den höchsten Umweltauswirkungen als repräsentatives Produkt für die Berechnung der Ökobilanzergebnisse verwendet wurde (Worst-Case-Ansatz). Modified mineral mortars are used for the following applications: Module 1: Modified mineral mortars as repair mortar for the protection and repair of concrete structures 1.1 Products used to restore and/or replace defective concrete 1.2 Products to protect reinforcement, necessary to extend the service life of a concrete structure exhibiting deterioration Module 2: Adhesives based on modified mineral mortars 2.1 Products for bonding ceramic tiles as well as natural stone for internal and external installations on walls, floors and ceilings 2.2 Products for bonding thermal insulation composite panels Module 3: Modified mineral mortars as joint fillers Products for joint filling of wall and floor coverings made of ceramic tiles as well as natural stone for indoor and outdoor applications Module 4: Modified mineral mortars as screed, floor levelling compounds, fillers, flowing screed Products for screed/synthetic resin screed for use in floor constructions Module 5: Modified mineral mortars as levelling compounds for walls and ceilings Products for levelling and repairing rough, uneven walls, for repairing grit spots, closing blowholes and modelling broken corners and edges Module 6: Modified mineral mortars as grouts Products for grouting on holes, recesses, concrete precast columns, foundations and for anchoring machine components indoors and outdoors Module 7: Modified mineral mortars for liquid applied products for waterproofing of buildings Products for providing cement-based waterproofing surfaces in structural and civil engineering. For use in new and old buildings as well as beneath tiles 7.1 Liquid-applied water impermeable products for use beneath ceramic tiling 7.2 Products for waterproofing with mineral waterproofing slurries or flexible polymer modified thick coatings 7.3 Products for water proofing in conjunction with ceramic tiles 7.4 Products for waterproofing with flexible polymer modified mineral thick coatings Module 8: Modified mineral mortars for waterproofing floors and/or walls inside buildings Products for watertight covering in wet rooms inside buildings Modifizierte mineralische Mörtel werden für die folgenden Anwendungen eingesetzt: Modul 1: Modifizierte mineralische Mörtel als Instandsetzungsmörtel für den Schutz und die Instandsetzung von Betonbauwerken 1.1 Produkte für die Instandsetzung und/oder den Ersatz von schadhaftem Beton 1.2 Produkte zum Schutz der Bewehrung, die notwendig sind, um die Lebensdauer eines schadhaften Betonbauteils zu verlängern Modul 2: Klebstoffe auf Basis von modifizierten mineralischen Mörteln 2.1 Produkte zum Verkleben von keramischen Fliesen und Platten sowie von Naturstein für Innen- und Außenverlegungen an Wänden, Böden und Decken 2.2 Produkte für die Verklebung von Wärmedämm-Verbundplatten Modul 3: Modifizierte mineralische Mörtel als Fugenfüller Produkte zum Verfugen von Wand- und Bodenbelägen aus keramischen Fliesen und Platten sowie Naturstein im Innen- und Außenbereich Modul 4: Modifizierte mineralische Mörtel als Estrich, Bodenausgleichsmassen, Spachtelmassen, Fließestrich Produkte für Estrich/Kunstharzestrich für den Einsatz in Fußbodenkonstruktionen Modul 5: Modifizierte mineralische Mörtel als Nivelliermassen für Wand und Decke Produkte zum Ausgleichen und Ausbessern von rauen, unebenen Wänden, zum Ausbessern von Splittstellen, Schließen von Lunkern und Modellieren von ausgebrochenen Ecken und Kanten Modul 6: Modifizierte mineralische Mörtel als Fugenmörtel Produkte zum Verpressen von Löchern, Aussparungen, Betonfertigteilstützen, Fundamenten und zur Verankerung von Maschinenteilen im Innen- und Außenbereich Modul 7: Modifizierte mineralische Mörtel für flüssig aufzubringende Produkte zur Bauwerksabdichtung Produkte für die Herstellung von Abdichtungsflächen auf Zementbasis im Hoch- und Tiefbau. Für den Einsatz im Neu- und Altbau sowie unter Fliesen und Platten 7.1 Flüssig aufzubringende wasserundurchlässige Produkte für die Verwendung unter keramischen Fliesen und Platten 7.2 Produkte für Abdichtungen mit mineralischen Dichtungsschlämmen oder flexiblen polymermodifizierten Dickbeschichtungen 7.3 Produkte für Abdichtungen in Verbindung mit keramischen Fliesen und Platten 7.4 Produkte für die Abdichtung mit flexiblen polymermodifizierten mineralischen Dickbeschichtungen Modul 8: Modifizierte mineralische Mörtel für die Abdichtung von Böden und/oder Wänden innerhalb von Gebäuden Produkte für die Abdichtung von Feuchträumen innerhalb von Gebäuden EPD Mineral factory-made mortar.pdf average dataset GaBi Database (all versions) GaBi database SP40 2020 Scope: This verified EPD entitles the holder to bear the symbol of the Institut Bauen und Umwelt e.V. It exclusively applies to products produced in Europe and for a period of five years from the date of issue. This EPD may be used by members of FEICA, EFCC, DBC and IVK and their members provided it has been proven that the respective product can be represented by this EPD. For this purpose, a guideline is available at the secretariats of the four associations. The members of the associations are listed on their respective websites. System boundary: Modules A1, A2 and A3 are taken into consideration in the LCA: - A1 Production of preliminary products - A2 Transport to the plant - A3 Production incl. provision of energy, production of packaging as well as auxiliaries and consumables and waste treatment - A4 Transport to site - A5 Installation, product applied into the building during A5 phase operations and packaging disposal. The end of life for the packaging material considered is described below: -Incineration, for materials like plastic, wood and paper. -C1-C2-C4-D The building deconstruction (demolition process) takes place in the C1 module which considers energy generation and consumption of diesel and all the emissions connected with the fuel-burning process to run the machines. After the demolition, the product is transported to the end-of-life processing (C2 module) where all the impacts related to the transport processes are considered. For precautionary principle and as a worst-case scenario, landfilling is the only end-of-life scenario considered. This is modelled by the landfill process (module C4) where the product ends its life cycle. Module D accounts for potential benefits that are beyond the defined system boundaries. Credits are generated during the incineration of packaging that is occurring in the A5 module. Modified mineral mortar, group 1 .pdf Institut Bauen und Umwelt e. V. DIN EN 15804+A2 ISO 14025 FEICA - Association of the European Adhesive and Sealant Industry Sphera Solutions GmbH 2022-09-26T16:17:34.124 ILCD Format EPD-Datenformaterweiterungen v1.2 EPD Data Format Extensions v1.2 00.01.000 Modified mineral mortars, group 1 Institut Bauen und Umwelt e. V. EPD-DBC-20220217-IBF1-EN FEICA - Association of the European Adhesive and Sealant Industry true Free of charge for all users and uses None Institut Bauen und Umwelt e. V. Modified mineral mortar, group 1 () 1 Renewable primary energy as energy carrier (PERE) Erneuerbare Primärenergie als Energieträger (PERE) General reminder flow Input MJ 0.980574522542 0.03742891085 0.7424737059 1.346664462E-05 0.0005879639154 0.02922025026 -0.1297654717 Renewable primary energy resources as material utilization (PERM) Erneuerbare Primärenergie zur stofflichen Nutzung (PERM) General reminder flow Input MJ 0.721 0 -0.721 0 0 0 0 Total use of renewable primary energy resources (PERT) Total erneuerbare Primärenergie (PERT) General reminder flow Input MJ 1.701574522242 0.03742891085 0.02147370594 1.346664462E-05 0.0005879639154 0.02922025026 -0.1297654717 Non renewable primary energy as energy carrier (PENRE) Nicht-erneuerbare Primärenergie als Energieträger (PENRE) General reminder flow Input MJ 8.86410354566 0.6665212993 0.2009814056 0.004275033664 0.1866512114 0.2231799729 -0.5924849711 Non renewable primary energy as material utilization (PENRM) Nicht-erneuerbare Primärenergie zur stofflichen Nutzung (PENRM) General reminder flow Input MJ 1.0466 0 -0.0866 0 0 0 0 Total use of non renewable primary energy resources (PENRT) Total nicht erneuerbare Primärenergie (PENRT) General reminder flow Input MJ 9.91070354586 0.6665212993 0.114381406 0.004275033664 0.1866512114 0.2231799729 -0.5924849711 Use of secondary material (SM) Einsatz von Sekundärstoffen (SM) General reminder flow Input kg 0 0 0 0 0 0 0 Use of renewable secondary fuels (RSF) Erneuerbare Sekundärbrennstoffe (RSF) General reminder flow Input MJ 0 0 0 0 0 0 0 Use of non renewable secondary fuels (NRSF) Nicht erneuerbare Sekundärbrennstoffe (NRSF) General reminder flow Input MJ 0 0 0 0 0 0 0 Use of net fresh water (FW) Einsatz von Süßwasserressourcen (FW) General reminder flow Input m^3 0.0024602223382738 4.334011039E-05 0.0005707662664 2.415691569E-08 1.054709256E-06 5.626306054E-05 -0.0001502693355 Hazardous waste disposed (HWD) Gefährlicher Abfall zur Deponie (HWD) General reminder flow Output kg 2.59508550523903E-05 3.10177918E-08 2.595666701E-07 4.146554762E-13 1.810417251E-11 3.401435298E-09 -2.362969697E-10 Non hazardous waste disposed (NHWD) Entsorgter nicht gefährlicher Abfall (NHWD) General reminder flow Output kg 0.031171411207256 0.0001020032654 0.01437438841 4.370943384E-07 1.908387025E-05 1.121965089 -0.0002741642452 Radioactive waste disposed (RWD) Entsorgter radioaktiver Abfall (RWD) General reminder flow Output kg 0.00024629654809749 8.249775164E-07 3.742814976E-06 4.588528806E-09 2.00338647E-07 2.539776442E-06 -4.431452877E-05 Components for re-use (CRU) Komponenten für die Wiederverwendung (CRU) General reminder flow Output kg 0 0 0 0 0 0 0 Materials for recycling (MFR) Stoffe zum Recycling (MFR) General reminder flow Output kg 0 0 0 0 0 0 0 Materials for energy recovery (MER) Stoffe für die Energierückgewinnung (MER) General reminder flow Output kg 0 0 0 0 0 0 0 Exported electrical energy (EEE) Exportierte elektrische Energie (EEE) General reminder flow Output MJ 0 0 0.148257768 0 0 0 0 Exported thermal energy (EET) Exportierte thermische Energie (EET) General reminder flow Output MJ 0 0 0.2663361245 0 0 0 0 Global Warming Potential total (GWP-total) Globales Erwärmungspotenzial total (GWP-total) kg CO_(2)-Äq. 0.488489883591 0.05056869273 0.1045855745 0.0003123377724 0.01387554814 0.01710497917 -0.03503028537 Global Warming Potential fossil fuels (GWP-fossil) Globales Erwärmungspotenzial fossil (GWP-fossil) kg CO_(2)-Äq. 0.55756339687 0.05001774394 0.01356193819 0.0002984825288 0.01326742394 0.01700229261 -0.03492364991 Global Warming Potential biogenic (GWP-biogenic) Globales Erwärmungspotenzial biogen (GWP-biogenic) kg CO_(2)-Äq. -0.0694863895022 0.0001459963772 0.09101791238 1.384807583E-05 0.0006078112543 5.375278598E-05 -8.211375998E-05 Global Warming Potential luluc (GWP-luluc) Globales Erwärmungspotenzial luluc (GWP-luluc) kg CO_(2)-Äq. 0.0004128762469135 0.0004049524083 5.72388491E-06 7.167787898E-09 3.129510547E-07 4.893377335E-05 -2.452169679E-05 Depletion potential of the stratospheric ozone layer (ODP) Abbau Potential der stratosphärischen Ozonschicht (ODP) kg CFC11-Äq. 2.8143185486491E-11 6.011213874E-18 2.81445211E-13 3.179409215E-20 1.388154172E-18 6.304311672E-17 -3.65558339E-16 Acidification potential of land and water (AP) Versauerungspotenzial von Boden und Wasser (AP) mol H^(+)-Äq. 0.00179773421334 0.0001498926975 3.496756262E-05 4.038997788E-06 4.185309347E-05 0.0001219728574 -4.897745357E-05 Eutrophication potential aquatic freshwater (EP-freshwater) Eutrophierungspotenzial Süßwasser (EP-freshwater) kg PO_(4)-Äq. 9.16184639545E-07 1.520183368E-07 1.489525183E-08 6.445786783E-11 2.814279386E-09 2.920241075E-08 -4.515892112E-08 Eutrophication potential aquatic marine (EP-marine) Eutrophierungspotenzial Salzwasser (EP-marine) kg N-Äq. 0.000345324255215 6.675668916E-05 8.934066799E-06 1.832029964E-06 1.922789416E-05 3.139298679E-05 -1.265973453E-05 Eutrophication potential terrestrial (EP-terrestrial) Eutrophierungspotenzial Land (EP-terrestrial) mol N-Äq. 0.00372447774469 0.0007476681029 0.0001139081491 2.006400454E-05 0.0002116490558 0.0003449550378 -0.0001356406634 Formation potential of tropospheric ozone photochemical oxidants (POCP) Bildungspotential für troposphärisches Ozon (POCP) kg NMVOC-Äq. 0.0013344051859 0.000131914175 2.828171157E-05 5.50610781E-06 3.797117409E-05 9.506606618E-05 -3.63712366E-05 Abiotic depletion potential for non fossil resources (ADPE) Potenzial für den abiotischen Abbau nicht fossiler Ressourcen (ADPE) kg Sb-Äq. 5.73542938436E-08 3.585865224E-09 7.918211873E-10 9.032648622E-12 3.94372288E-10 1.52710448E-09 -5.743867748E-09 Abiotic depletion potential for fossil resources (ADPF) Potenzial für den abiotischen Abbau fossiler Brennstoffe (ADPF) MJ 9.90542393677 0.6658485865 0.1239193296 0.004270853354 0.1864686959 0.2230750123 -0.5924230521 Water use (WDP) Wassernutzung (WDP) m^(3) world-Äq. deprived 0.087935918746949 0.0004470510047 0.0242301948 5.901432348E-07 2.576610112E-05 0.001782280587 -0.003629962351 Incidence of disease due to PM emissions (PM) Auftreten von Krankheiten aufgrund von Feinstaubemissionen (PM) Disease incidence Human exposure efficiency relative to U235 (IR) Wirkung durch Exposition des Menschen mit U235 (IR) kBq U235-Äq. Comparative toxic unit for ecosystems (ETP-fw) Toxizitätsvergleichseinheit für Ökosysteme (ETP-fw) CTUe Comparative toxic unit for humans (carcinogenic) (HTP-c) Toxizitätsvergleichseinheit für Menschen (krebserregend) (HTP-c) CTUh Comparative toxic unit for humans (noncarcinogenic) (HTP-nc) Toxizitätsvergleichseinheit für Menschen (nicht krebserregend) (HTP-nc) CTUh Soil quality index (SQP) Bodenqualitätsindex (SQP) SQP